大涡模拟Smagorinsky模型用于磨粒流精密加工喷嘴的质量控制研究

为研究固液两相磨粒流加工喷嘴小孔过程中的流场分布、涡旋形成规律及涡旋的存在对磨粒流加工的影响机制，采用Smagorinsky亚格子模型对磨粒流加工喷嘴小孔的流道进行大涡数值模拟，并使用磨粒流对变直径喷嘴工件进行加工试验。数值模拟发现磨粒流流体中磨粒与壁面的碰撞与剪切作用随流体的速度增大而增大，同一截面的速度存在速度差，其中还伴随涡旋的存在；通过试验研究发现：经固液两相磨粒流加工后的喷嘴小孔表面质量得到明显提高，喷嘴经过四次不同入口速度的磨粒流加工后大孔处表面粗糙度Ra由1.24 μm降至0.542 μm，小孔处表面粗糙度Ra由1.21 μm降至0.437 μm。结论显示固液两相磨粒流加工技术可有效提高被加工喷嘴工件的内表面质量，加工时同一截面的速度存在速度差，速度差的存在利于涡旋的形成，涡旋的存在利于提高磨粒流加工过程的剪切作用，有助于获得高质量的喷嘴小孔内通道表面。     

全局力平衡PDC钻头布齿优化设计

针对聚晶金刚石复合片(PDC)钻头在钻井破岩过程中因受力不平衡，导致钻井倾斜、井径扩大、钻头产生横向振动和涡动，造成钻头早期失效的问题，基于已有PDC钻头切削力学知识，构建了PDC钻头弯曲力矩及全局力平衡布齿优化设计模型，并提出模型求解方法。布齿设计实例结果表明，采用全局力平衡布齿设计方法得到的布齿结构可使PDC钻头在不同进尺条件下均能保持全局力平衡状态，尤其低进尺（小于1 mm）时的力平衡状态得到极大改善，提高了PDC钻头的钻井稳定性，对于改善钻头受力、提升钻头使用寿命、提高钻井质量与效率具有重要意义。     

异质性环境规制对绿色全要素生产率的影响机制——基于能源消费结构的调节作用

为探讨能源消费结构调节下异质性环境规制对绿色全要素生产率的影响机制，论文利用SBM方向距离函数测得全国各省市“经济-资源-环境-社会”四位一体的绿色全要素生产率，并将环境规制工具分为命令控制型、经济激励型、治理投入型和公众参与型4类，构建了空间杜宾模型以及门槛效应模型，进而得出在能源消费结构调节下，异质性环境规制对绿色全要素生产率的直接作用、间接作用以及空间溢出效应。研究结果表明：1）经济激励型和公众参与型环境规制通过调节能源消费结构对当地和邻地的绿色全要素生产率产生影响；2）在门槛检验方面，能源消费结构对命令控制型、经济激励型和公众参与型环境规制影响绿色全要素生产率存在门槛效应，同时在能源消费结构调节下，命令控制型和经济激励型环境规制对其本身对绿色全要素生产率的间接作用存在门槛效应。建议政府在制定环境规制时要考虑到其与能源消费结构的交互作用，并且在不同能源消费水平地区采用适宜的规制方法和强度，以更好地发挥环境规制作用。     

高强不锈钢绞线网与ECC黏结-滑移关系模型

高强不锈钢绞线网与ECC的黏结是二者协同工作的基础，且黏结 滑移关系模型是其黏结性能的综合反映，故通过对17组51个高强不锈钢绞网增强ECC薄板试件进行单边拉拔试验，研究横向钢绞线间距、纵向钢绞线直径和相对锚固长度等因素对钢绞线网在ECC中黏结性能的影响规律。试验结果表明，横向钢绞线的设置可使黏结破坏由脆性破坏转变为延性破坏；高强不锈钢绞线网与ECC的黏结滑移曲线可分为5个阶段，分别为上升段、微降段、延性强化段、下降段和残余段。基于试验结果，对钢绞线网在ECC中的黏结破坏特征和黏结 滑移机理进行分析，在相关黏结-滑移关系模型的基础上，提出钢绞线网与ECC的黏结 滑移关系模型，并进行模型参数分析。所提模型及模型参数计算公式与试验结果吻合良好，能较好地反映钢绞线网与ECC的界面黏结滑移特征。     

大坝服役非概率可靠性分析方法

针对大坝服役可靠性影响因子具有非概率不确定特征的情况,建立了定量刻画大坝服役可靠性非概率影响因子的Info-gap模型,运用Info-gap决策理论和体积比非概率可靠性度量方法,提出了大坝服役非概率可靠性分析方法,拟定了大坝服役非概率目标可靠度。应用提出的非概率方法分析了某大坝结构服役可靠性,各功能模式可靠性分析结果说明了该方法的工程适用性,同时也验证了所拟定大坝服役非概率目标可靠度的合理性。     

Short communication: In vitro rumen gas production and starch degradation of starch-based feeds depend on mean particle size

Our objective was to model the effect of mean particle size (mPS) on in vitro rumen starch degradation (IVSD) and the kinetics of gas production for different starch-based feeds. For each feed, 2 batches of the same grains were separately processed through 2 different mills (cutter or rotor speed mills), with or without different screens to achieve a wide range of mPS (0.32 to 3.31 mm for corn meals; 0.19 to 2.81 mm for barley meals; 0.16 to 2.13 mm for wheat meals; 0.28 to 2.32 mm for oat meals; 0.21 to 2.36 mm for rye meals; 0.40 to 1.79 for sorghum meals; 0.26 to 4.71 mm for pea meals; and 0.25 to 4.53 mm for faba meals). The IVSD data and gas production kinetics, obtained by fitting to a single-pool exponential model, were analyzed using a completely randomized design, in which the main tested effect was mPS (n = 6 for all tested meals, except n = 7 for corn meals and n = 5 for sorghum meals). Rumen inocula were collected from 2 fistulated Holstein dairy cows that were fed a total mixed ration consisting of 16.2% crude protein, 28.5% starch, and 35.0% neutral detergent fiber on a dry matter basis. The IVSD, evaluated after 7 h of rumen incubation, decreased linearly with increasing mPS for corn, barley, wheat, rye, pea, and faba meals, and decreased quadratically with increasing mPS for the other meals. The y-axis intercept for 7-h IVSD was below 90% starch for corn, barley, and rye feeds and greater than 90% for the other tested feeds. The mPS adjustment factors for the rate of rumen starch degradation varied widely among the different tested feeds. We found a linear decrease in starch degradation with increasing mPS for barley, wheat, rye, and pea meals, whereas we noted a quadratic decrease in starch degradation for the other tested meals. Further, we observed a linear decrease in the rate of gas production with increasing mPS in each tested feed, except for pea meal, which had a quadratic relationship. For each 1 mm increase in mPS, the gas production was adjusted by ?0.009 h^?1 for corn, ?0.011 h^?1 for barley, ?0.008 h^?1 for wheat, and ?0.006 h^?1 for faba, whereas numerically greater adjustments were needed for oat (?0.022 h^?1), rye (?0.017 h^?1), and sorghum (?0.014 h^?1). These mPS adjustment factors could be used to modify the starch-based feed energy values as a function of mean particle size, although in vivo validation is required.     

Reduced basis method for managed pressure drilling based on a model with local nonlinearities

To circumvent restrictions of conventional drilling methods, such as slow control actions and inability to drill depleted reservoirs, a drilling method called managed pressure drilling (MPD) has been developed. In MPD, single-phase flow processes can be modeled as a feedback interconnection of a high-order linear system and a low-order nonlinear system. These nonlinearities appear locally both inside and at the boundaries of the computational domain. To obtain a fast simulation platform for real-time purposes (eg, online model-based controller implementation), model order reduction is required for MPD. However, the local nonlinearities render applying model order reduction techniques challenging. In this study, a new approach is proposed to deal with such nonlinearities within the reduced basis (RB) context and it is successfully tested on a model for MPD. Contrary to the classical RB technique, the proposed approach not only does not generate nonphysical spikes at the locations of these local nonlinearities but also yields high speedup factors. The obtained reduced-order model can be used for efficient online simulation and controller design for drilling systems with MPD.     

临近空间载人舱舱门密封特性研究

为研究临近空间载人舱舱门密封特性,对临近空间载人舱舱门P形橡胶密封圈进行有限元压缩行为仿真分析,分析P形橡胶密封圈主副密封面密封接触宽度和接触应力随舱门间隙与舱门行程变化的规律,并根据该规律给出舱门压缩行程和舱门密封间隙的设计推荐值。基于ROTH泄漏模型推导出P形橡胶密封圈的总漏率模型,并计算该泄漏模型的稳态漏率值。通过舱门密封试验,对P形橡胶密封圈的总漏率进行验证。P形橡胶密封圈总漏率计算值与试验结果基本吻合,验证了P形橡胶密封圈总漏率模型的有效性。     

中国省际绿色技术创新效率测度及影响因素研究

文章基于2011—2017年中国30个省份面板数据，运用super-SBM模型对绿色技术创新效率进行测算，并利用ML指数对绿色技术创新效率进行动态分析，最后通过空间滞后模型分析影响效率的关键因素。研究结果表明：中国绿色技术创新效率呈逐渐增长的趋势，但整体效率偏低，有较大进步空间；中国绿色技术创新效率存在明显区域差异，呈现由东部向西部递减的格局；绿色技术创新水平的提高是技术效率和技术进步共同贡献的结果；产业结构、区域开放程度和教育水平对绿色技术创新效率产生积极的正向影响，环境规制和研发投入强度对绿色技术创新效率影响不显著。